The spinner rig is one of the most popular rigs used for Lake Fishing for Trout. There are different types of spinners that can be used so choosing the perfect one and learning how to set it up is extremely important.
So, if you are about to go fishing then do read our “Lake Fishing for Trout” using spinner rigs: The ultimate guide.
For any successful fishing trip, one needs to have the necessary gear. Several tools that are essential while lake fishing for trout are trout lures, floating jig heads, soft plastic, split shots, bullet sliding sinker, barrel swivels, snap swivels, and hooks sized 8-14, plastic beads, bobber stops, slip bobbers, and fixed bobbers.
The most important factor in determining success during lake fishing for trout is using the right rig. The three basic rigs include rigs that show bait hanging below a float, rigs that present bait near the bottom with the weight, and rigs that allow the fisher to cast and retrieve an artificial lure.
Every water body is different, but spinner rigs, in particular, are proficient in pulling out trout from relatively clear water bodies.
The spinner rig is the most common lure rig. Its great hooking ability and versatility mean that it is used in many settings to deadly effect. The rig itself can be used with different spinners, which we are going to mention below. The spinner rig is meant to be used with pop-up hook baits but you can always experiment with other types of lures.
Advantages of using a Spinner rig to Lake Fish for Trout
The main advantage of the spinner rig is its 360-degree movement. The hook is mounted on a quick change swivel allowing it to rotate in all directions. This is perfect when you are Lake Fishing for Trout and the fish are coming from every direction.
Secondly, the pop up is presented very low on the lakebed. So while your hook bait is elevated enough to keep it clear of stones and lake debris, it does not bob around unnaturally. This makes it much more likely for your hook bait to be gobbled up by the trout.
Another advantage is that in order to change the hook you don’t have to take off the entire hook line. You can simply detach it from the quick change swivel and put on a new one.
Setting up a Spinner rig
The step-by-step process of setting up a spinner rig is:
- Tie your main line to a swivel and put one or two split shot weights a little bit upwards of the swivel.
- Then a fluorocarbon leader of about 2 to 4 feet would be tied to the other end of the swivel and the lure would be tied leader’s other end.
- The rig will then be cast out and the retrieving speed should be adjusted according to the depth in which you are fishing.
It works effectively in both shallow as well as deep water. However, the speed of the winds needs to be kept in check or it might not attract fish.
Here are some of the most important spinners and their applications.
Rooster tail spinners
Rooster tails are mostly used if you want to fish in a river or a stream, generally where the water temperature is 60 degrees or above. In most cases, the rooster tail is used to catch fish in the middle of the water column. They are used with heavy-action spinning rods.
The lure will be tied to the end of your line and tipped with a small piece of live or artificial bait. This will then be cast out in the water and retrieved. A heavier lure would be needed in case the trout are found near the bottom. Adjusting the speed and using a zigzag pattern for the line can help in attracting fish that might not bite normally.
Roster tails are easy to use and are very durable in their design. They come in different shapes and colors, which means they are suitable for a variety of trout. The design of the rooster tail hook is very strong and capable of landing fish that have a large size.
This spinner works the best when it is paired with light spinning gear. It is mostly used in water that is not clear and has a lot of debris. The main line is tied to the swivel and split shot weights are put above the swivel. The panther martin is then tied to the other end of the leader and cast out.
Panther Martins have an edge over other blades since they are large which allows them to spin faster than other rigs. The large size of the blade causes powerful vibrations that attract more fish.
This is also the only kind of spinner that does not need any additional weight to reach the deep side.
Blue Fox Vibrax
The Blue Fox Vibrax is appropriate for every kind of water bodies, from shallow to deep, owing to their versatility. It is a shiny spinner with a loud noise, which attracts trout. If you are Lake Fishing for Trout with it, just simply cast it out and let it sink for as long as you want. Just make sure the spinner is spinning properly by slowly winding it in.
This spinner is deep, which makes it perfect for getting down to areas where the trout are holding. Blue fox Vibrax is one of the best spinners you can use to eliminate line twists. It works well in dark water as well because of its colored lures that look attractive.
This spinner is mostly used in shallow lakes or ponds. However, it can be used in all other water bodies as well. It is designed to be a fly as well as a spinner and that makes it ideal for catching trout. Flashing lights and the speed of this spinner lure fish in fast. Joe’s Flies Short Striker is used best tied directly to 4 to 8 lb monofilament.
Using a swivel is not recommended for this spinner. It contains a single and treble hook which increases the chances of hooking trout.
Lake fishing for trout is an activity that one gains expertise in only after practicing. There are many rigs out there and each of them is ideal for different situations. Spinning rigs, however, can be used everywhere with a high success rate. The spinners mentioned above have made lake fishing for trout convenient and enjoyable.
We hope that our “Lake Fishing for Trout” using spinner rigs: The ultimate guide has been helpful in your quest for trout!